Install Instructions

Installation:

Step 1 - Inflate board and determine where you would like to place the mounts. The more you use the more the lights will take the shape of your board. Clean areas where Velcro will be attached and avoid areas where the board will fold. 

Step 2 - Clean areas where velcro will be attached. You can use soapy water with a mild detergent. Rinse and allow to dry before placing the velcro. 

Step 3 - Place a velcro at each spot you want a mount and press it firmly on to the board. We like to put two towards the front of the board so that both ends are at the front of the board and the control module can be placed under your straps and is easily accessible.

Step 4 - Place a velcro on each of the mounts you are using.

Step 5 - Allow velcro to adhere to the board for at least 2 hours but we recommend 24 hours before putting too much tension on them. 

Step 6 - Place the mounts on the board and run the light through each one. We recommend starting at the nose but you can start anywhere. Two mounts have a set screw included, before running the light through make sure the set screws are backed out enough. These should be used at the two ends so you can pull the light for a tight line and then screw them in. Be careful not to over tighten the screw as it does not take much to hold it in place.

Step 7 - You are finished. To remove simply lift the mounts off. Just lift off and then next time your install is already set and you can simply place the mounts back on the board.

Step 1 - Inflate board and determine where you would like to place the mounts. The more you use the more the lights will take the shape of your board. Clean areas where Velcro will be attached and avoid areas where the board will fold. 

Step 2 - Clean areas where velcro will be attached. You can use soapy water with a mild detergent. Rinse and allow to dry before placing the velcro.

Step 3 - Place a velcro at each spot you want a mount and press it firmly on to the board. We like to put two towards the front of the board so that both ends are at the front of the board and the control module can be placed under your straps and is easily accessible.

Step 4 - Place a velcro on each of the mounts you are using.

Step 5 - Allow velcro to adhere to the board for at least 2 hours but we recommend 24 hours before putting too much tension on them.

Step 6 - Place the mounts on the board and run the light through each one. We recommend starting at the nose but you can start anywhere. Two mounts have a set screw included, before running the light through make sure the set screws are backed out enough. These should be used at the two ends so you can pull the light for a tight line and then screw them in. Be careful not to over tighten the screw as it does not take much to hold it in place.

Note - When making the connection for module, align the two arrows. If it is reversed the lights will not work.

Step 7 - You are finished. To remove simply lift the mounts off. Just lift off and then next time your install is already set and you can simply place the mounts back on the board.

Step 1 - It helps to lay out the lights around the kayak to determine the best spots for the mounts. Things to keep in mind when determining mount locations:

• Find flat or near flat spots
• Have one mount near the cockpit so you can place the controller inside
• Set screws will be placed at each end of light in order to pull the lights tight and stay in place. 
• Clean areas with soapy water and allow to dry.

Step 2 - We like to start with the controller end of the light. Place a velcro in a position that allows you to place the controller in the kayak cockpit. This mount will use one of the set screws to hold the light in position. 

Step 3 - Work your way around the kayak placing the velcro in your desired locations. Push the velcro firmly on the kayak and attach the mount. Allow velcro to adhere to board for at least 3 hours but we recommend 24 hours before putting too much tension on them.

Step 4 - Run the lights through the mounts starting with the mount by the cockpit. Place a set screw on the first and last mounts. With one end tightened down, pull the lights gently and then tighten down the last set screw.

Step 5 - You are finished installing the lights. The next time you use the lights you can simply reattach them in each position. It is helpful to have the Allen wrench to loosen one end when attaching the lights going forward.

Installation: